#ZOC TERMINAL TUTORIAL SERIAL PORT HOW TO#
#ZOC TERMINAL TUTORIAL SERIAL PORT INSTALL#
#ZOC TERMINAL TUTORIAL SERIAL PORT DRIVERS#
#ZOC TERMINAL TUTORIAL SERIAL PORT MANUAL#

I'm not sure if this is a related problem.

Although, when I try to open a Visa test panel in MAX the program crashes. According to MAX the device is working properly. The termination character for Venus2 is a space for transmitting commands and ASCII CR LF at the end of received data. The write command getaxisno_ should reply with the default axis no which is 1. The time-out is set to 10s, I have a wait of 1s before read and 0.5s between each write (the characters are written individually incase that was the problem).

#ZOC TERMINAL TUTORIAL SERIAL PORT DRIVERS#

The Visa drivers have just been installed.Īfter some research I have added a 'Set I/O buffer size' as advised by A terminal emulator enables a host computer to access a remote computer using a command-line or graphical interface. I have attached some sample code for LV 10.0.1(64bit) and the OS is Windows Server Enterprise 2008. Even for the basic example there has never been any bytes at the serial port after the write. I have tried adaptations of LV's Basic Serial Read and Write example. The Pollux box has an RS232/485 connection to the computer.

#ZOC TERMINAL TUTORIAL SERIAL PORT HOW TO#

Then, from another terminal on a remote PC connected to the same network, use the command described in How to perform ssh connection.I'm having problems communicating with a Pollux box controlling a stepper motor (both from Micos). If the network connection is through Ethernet then 'InterfaceNetwork' = 'Eth0', else if the network connection is using Wifi then 'InterfaceNetwork' = 'WLAN0'Įth0 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx: FB

using a console (see chapter Remote terminal via Serial link (UART/USB).

if it exists, using the board user interface (Terminal window or specific application).

To do so, first get the IP address of the board: The board can also be accessed via the network through Ethernet connection, using ssh. You can for example reboot the board and see the boot sequence. The setup is correct when you can send Linux ® commands through the terminal emulator and get feedback. You are sending the string Enter (like typing E, N, T, E, R ).

#ZOC TERMINAL TUTORIAL SERIAL PORT MANUAL#

More information on the board serial port can generally be found in the hardware user manual of the board.

Open a terminal emulator application on your PC and configure with the serial setup menu the USB port to be used and the baud rate of the serial link (in general 115200 baud).

Īny of the Windows ® terminal emulator applications can be used. On the terminal, the prompt is changed information on Minicom can be found at the following link. See below example for a standard UART (ttyS0) or STLink interface (ttyACM0): See How to use TTY with User Terminal article to find the appropriate tty instance to be used. Hardware flow control is generally set to off (default value is on) and a baud rate of 115200 is usual. The UART configuration that is set with the below command has to match the one from your board: to be checked within board user manual.

#ZOC TERMINAL TUTORIAL SERIAL PORT INSTALL#

If a message indicating Minicom does not exist, then install it:.You need first to check that Minicom is installed on your PC. Pictures describing board connections can be found in Category:STM32_MPU_boards 1.1 On Linux ® PC If you are prompted for drivers, please see the Drivers section. Your computer should automatically install the necessary drivers and create a COM port on your computer. 1 Remote terminal via serial link (UART/USB)ġ Remote terminal via serial link ( UART/USB) įirst of all, you need to connect your host PC to the board via UART.ĭepending on the board, some additional materials may be needed to physically interconnect the board to the console serial port (extension board or adapter to interconnect the UART from the board to the USB PC input). Plug the micro-B USB cable into a USB port on your computer and the other end into the Serial Basic.

Zoc terminal tutorial serial port